non - insulated steel door - model 692
SPECIFICATIONS

PA R T 1  G E N E R A L
1.01 Section Includes
A . Upward Acting Sectional Steel Doors,
including unit sections, brackets, tracks, glazing,
counter balance mechanisms, and hardware.
1.02 Related Work
A . Opening preparation, miscellaneous or
structural steel, finish or field painting, electrical
wires, wiring, disconnect switches, conduit are in
the scope of the work of other sections or trades.
B . Submit manufacturer's product data and
installation instructions for each type of sectional
door. Include both published data and any
specific data prepared for this project.
1.03 Single Source Responsibility
A . Provide door, tracks, motors and accessories
from one manufacturer for each type of door.
Provide secondary components from source
acceptable to manufacturer of primary
components.

PA R T 2  P R O D U C T
2.01 Manufacturer
A . Upward Acting Sectional Steel Doors are to
be Clopay(r) Model 692 as manufactured by
Clopay Building Products Company, Inc.
2.02 Material/Construction
A . Ty p e : 21/8" (53.98 mm) thick, roll-formed 24
gauge (.022", (.56 mm) minimum) commercial
steel.
B . S i z e : Standard maximum door size is 18'2"
(5.54 m) wide by 16' (4.88 m) high.
C . S e c t i o n J o i n t : Sections to form weathertight
shiplap fit.
D . M a t e r i a l : Hot-dipped galvanized,
complying with ASTM A-924, A-653, standard
lift operating style with track and hardware;
complying with DASMA 102, commercial
application.
E . F i n i s h : Pre-finished interior and exterior
skins with 1 mil, three-coat baked-on polyester
top coat over primer on a phosphate coating.
1 . E x t e r i o r S k i n : Exterior woodgrain texture
steel skin with raised panel design. Color:
white, brown, almond.
2 . I n t e r i o r S k i n : Color: white.
2.03 Related Door Components
A . E n d S t i l e s : Galvanized steel primed with
baked on polyester top coat. Attachment hardware
to have pre-punched holes. Polyurethane
foam strips on end stiles to stop air and light
infiltration. Select one:
1 . 18 gauge (.049", (1.25 mm) minimum) single
end hinge style.
B . C e n t e r S t i l e s : 18 gauge (.049",
(1.25 mm) minimum). Stiles and roll-formed
section are fastened together with Tog-L-LocTM.
C. Hinge and Roller Assemblies: Hinges
and brackets to be 14 gauge (.070", (1.78 mm)
minimum) galvanized steel.
1 . Ten-ball steel rollers to be full-floating ball
bearing in case hardened steel races and
mounted to fit the taper of the track.
2 . Heavy-duty hinges and 12 gauge (.101",
(2.57 mm) minimum) adjustable roller
holders to be galvanized steel.
2 . 0 4 Tracks
A . H o r i z o n t a l Tr a c k : To be 14 gauge (.075",
(1.91 mm) minimum) galvanized steel reinforced
with 13 gauge (.085", (2.16 mm) minimum) galvanized
steel angles.
B. Rolled Galvanized Steel (select one):
Standard lift track, vertical lift track, high lift track,
follow-the-roof slope track, low headroom trackprovide:
2" (50.8 mm) or 3" (76.2 mm) as
required.
C . Ve r t i c a l Tr a c k s : To be 16 gauge (.060",
(1.52 mm) minimum) galvanized steel, tapered
and mounted for wedge type closing.
D. Mounting: Interior face mounted on a
prepared surface.
E . Track Mounting (select one):
1 . Bracket Mounting: Galvanized steel
mounting brackets 12 gauge (.101", (2.57 mm)
minimum) thick for wood jambs.
2 . Continuous or Reverse Galvanized
Steel Angle Mounting: 12 gauge (.101",
(2.57 mm) minimum) angle for steel or wood
jambs; splice plates 12 gauge (.101", (2.57 mm)
minimum).
2.05 Spring Counterbalance
A . S p r i n g s : Shall be torsion type, low stress,
helically wound, oil-tempered spring on a
galvanized steel tube or solid steel shaft. Wire
to provide 10,000 cycles minimum.
1 . 25,000 cycles
2 . 50,000 cycles
3 . 100,000 cycles
B. Cable Drums: Die cast aluminum.
C . C a b l e : Pre-formed galvanized steel aircraft
cable to provide a minimum of a 7:1 safety
factor.
2.06 Operation
A . O p e r a t i o n S h a l l B e : Manual push-up,
chain hoist, motor operated.
B. For Manual Operation: Requiring
maximum exertion of the greater of 5% of door
weight or 25 lbs. (111.2 N) force to open. Use pull
rope supplied.
2.07 Weatherstripping
A. Field-Installed Section Joint Seal
Tape:Neoprene foam seal, one-piece full length
between joint of sections.
B . Field-Installed Jamb/Header Weatherstripping:
Extruded vinyl, placed in moderate
contact with outside of door sections.
2.08 Bottom Sections
A . A s t r a g a l R e t a i n e r : Full length, .040"
(1.02 mm) aluminum.
B . A s t r a g a l : U-shaped flexible PVC vinyl.
C . S t e p P l a t e : 3" (76.2 mm) galvanized steel
step plate to be located on bottom section.
2.09 Locking
A . Inside spring loaded slide bolt lock on end
stile to securely engage slot in track.
1 . Optional - Inside spring loaded slide bolt lock
on end stile to securely engage slot in track.
2 . Optional - Outside keyed snap latch lock
assembly.
2.11 Options
A. Removable Mullions: 2" (50.80 mm)
Carry-away or Roll-away up to 14' (4.267 m) high.
B . G l a z i n g :
1. Window Size: 191/2" x 12"
(495.3 mm x 304.8 mm).
2 . Frame to be rigid Cellular PVC.
3 . Glass Available (select one):
a . SSB
b . 1/8" Plexiglass

PA R T 3  E X E C U T I O N
3.01 Examination
A . Verify that dimensions are correct and
project conditions are suitable for installation.
Do not proceed with installation until
unsatisfactory conditions have been corrected.
3 . 0 2 I n s t a l l a t i o n
A . I n s t a l l a t i o n : To be by an authorized
Clopay representative and in accordance with
manufacturer's instructions and standards.
B . Submit manufacturer's product data and
installation instructions for each type of
sectional upward acting door. Include both
published data and any specific data prepared
for this project.
N o t e t o S p e c i f i e r s . . . Please reference Ideal
Door(r) brand model C4RST.